What rearend swap should be used for more traction on a 93 c1500?

1. What's better 10-bolt or 12 bolt rear end?
2. Is limited slip differential the same as Positraction?
3. Is a GU6 rear end limited slip?
4. How strong is a GM 10-bolt rear end?
5. Is posi traction the same as limited slip?
6. How much horsepower can a 8.2 10 bolt handle?
7. Can you do a burnout with a limited slip differential?
8. Which is better limited slip or locking differential?
9. Is limited slip better than open?
10. Is a GT4 rear end posi?
11. What rear end does my S10 have?
12. Is a G80 limited slip?
13. How can you tell the difference between an 8.2 and 8.5 rear end?
14. What s10 has 8.5 rear end?
15. How do I know my differential gear ratio?

What's better 10-bolt or 12 bolt rear end?

First, the 10-bolt's pinion shaft diameter is 1.438 (25 splines) while the 12-bolt is 1.625 (30 splines) which makes the 12-bolt 13 percent larger in diameter and therefore stronger.

Is limited slip differential the same as Positraction?

The limited-slip differential is similar to the positraction differential, but allows the wheel with traction to have only a limited amount of greater power than the wheel that is slipping. ... A limited-slip differential will prevent the tire with less traction from separately spinning.

Is a GU6 rear end limited slip?

GU6 is a 3.42 gear, not limited slip.

How strong is a GM 10-bolt rear end?

But there are several models in the 10-bolt line-up. The smaller 7.5- and 8.2-inch 10-bolt rear axles can't transmit horsepower loads in excess of 400 hp. However, the 8.5- and 8.6-inch 10-bolts are extremely stout and effective rear differentials that can transmit up to 1,000 hp to the rear wheels.

Is posi traction the same as limited slip?

Despite the fact that a lot of folks confuse the terms “posi” or “Positraction” with “limited slip,” the fact is that the two are basically one and the same. Today, all positive traction systems are referred to as limited slip systems.

How much horsepower can a 8.2 10 bolt handle?

Roughly 550 to 600 HP total. No slicks, drag radials. No problems with the 8.2 at all. I used the stock diff., the Auburn would be better.

Can you do a burnout with a limited slip differential?

So going back to your question yes it is possible to perform a burnout with a limited slip differential and infect it would be a better burnout as both drive wheels would be getting equal amounts of power, it will prevent you spinning up just one single wheel and looking like an amateur.

Which is better limited slip or locking differential?

Limited slip differentials provide your vehicle with the best traction around. Locking differentials might give you good traction too, but the traction that you will experience with limited slip differentials is better. For starters, they will make it easier to turn on roads which are slippery and wet.

Is limited slip better than open?

If the other wheel spins in the opposite direction, you have an open differential. If it spins in the same direction, you have a limited slip differential, or LSD. When working properly, an open differential is the best riding, most comfortable option for everyday driving.

Is a GT4 rear end posi?

All Quadrasteers have G86 posi units. Normal rearends may have G80 posi units. QS rears all came with either 3.73 or 4.10 gears. 3.73s will be GT4, 4.10s are GT5.

What rear end does my S10 have?

Chevrolet S10 models generally use the GM 7.5-inch rear differential, however, certain models were equipped with the GM 8.5-inch differential. Both differentials were available as limited slip, positraction differentials.

Is a G80 limited slip?

"G80" is a GM order code for the limited slip diff; originally named "Positraction" by GM. . It's been the same order code for 40 years or more.

How can you tell the difference between an 8.2 and 8.5 rear end?

Another way to tell the difference between an 8.2 and an 8.5 rearend is to pull the cover and look at the bolt holding the spider gear crosspin. If it takes a 1/2-inch wrench to remove it, it's an 8.2. If it takes a 5/16-inch wrench to remove it, it's an 8.5.

What s10 has 8.5 rear end?

According to Chevy High Performance, the 7.5-inch was standard until 1993, when the previously optional 7.625-inch became standard. 1995 and newer S-trucks equipped with the high-output V6 were equipped with the 8.5-inch rear end.

How do I know my differential gear ratio?

Turn the wheel TWO revolutions and count the number of driveshaft turns. The number of driveshaft rotations will help you determine your rear axle ratio. For example, if it turned 3 and a half times, it's a 3.50:1 ratio. If it turned 4 and a quarter times, it's a 4.25:1 ratio.